スポンサーサイト
上記の広告は1ヶ月以上更新のないブログに表示されています。
新しい記事を書く事で広告が消せます。


スポンサー広告 | --:--:-- | Trackback(-) | Comments(-)
おすすめ
コンピュータの使用感は、本体の性能もさることながら、人が直に接するインターフェイスとなるマウス、キーボード、モニタ等によってかなり左右されます。特にCADソフトウエアを使う上では言うまでもありません。

おすすめマウス
Microsoft IntelliMouse Optical多ボタンマウスによってCADの操作性を向上させることができます。私は5ボタンの Microsoft IntelliMouse Optical を使っています。USB端子のあるMacならばClassicでもXでも使用できます。

キーボードを使わずに右クリックだけでコンテクストメニューを出すことができます。スクロールボタンで画面の拡大、縮小ができます(Classicでは挙動が違うようです)。また、左右の側ボタンをそれぞれ「shift+クリック」、「option+クリック」に設定すれば画面のパン、ズームがマウスだけで操作できるようになります。

マウス(ソール)の滑りが不十分に感じられる場合はこちらを参照下さい→トスベールでマウスのソール(足)を改良する

おすすめマウスパッド
* ダイソー 光学マウス対応マウスパッド 105円
* UCHIDA 「きりっこ」 下敷きタイプのカッティングマット

リンク・紹介・お勧め | 11:58:26 | Trackback(0) | Comments(-)
リンク・紹介
* Lemke Software GmbH ドイツのシェアウエアメーカ。GraphicConverter、CADintosh、FontBook、SnapsCleaner
* Yahoo! Groups: cadintoshmac 英語です。CADintoshの作者Thorsten Lemke氏も参加しています
* シェアウエア登録 Kagi 登録料の支払いはこちらでお願いします。
* CADintosh JP 旧サイト
* VA034381 Makoto Inoueのサイト。SnapsCleanerJP、Pd、Zerius Vocoder

CADintoshの使用事例
* Metallbau Schlosserei Thomas Sauter 製作にCADintosh?とレーザーを使用しているドイツの鉄工ファクトリー。"TECHNOLOGIE"のページにCADintoshのスクリーンショット
* Fräsentagebuch ドイツの旋盤機メーカー?"Zum Thema Software"のページにCADintosh
* 軽模型飛行機研究室 - 非対称DLG:Mutant Bird
* ポコマンボの庭 - ポコ庭「恐竜フェンス」のできるまで

* アスキーMacPeople2004.3.15+4.1号で紹介、付録CD-ROM収録されました。
* 平成16年度CAD利用技術者試験1級(実技)にCADintoshが利用可能との回答をCAD利用技術者試験センターより得ました。DXFファイルでの提出ですので文字化け等に注意の上、自己責任で利用下さい。
* Vector 週間総合ランキング(Macintosh)04.02.02~04.02.08 Macintosh総合16位「CADintosh X 5.1」(ビジネス部門では1位)


リンク・紹介・お勧め | 11:40:49 | Trackback(0) | Comments(-)
04 A Door
Exciteで和訳する(参考)

Next we will draw a door on the short inside wall. At the bottom left, select pen 2 that draws 0.35 mm thick lines. First draw a line parallel to the inside line of the bottom outside wall with a spacing of one meter and then another line parallel to the new line also with a spacing of one meter. The results should be the same as the following screenshot.

door14-2s.jpg

We only need the parts of the two new lines that are inside the inside wall. Zoom the picture to be make trimming easier. Hold down the Alt key and drag open a rectangle over the area to be enlarged. CADintosh does not only show a rectangle, but also all open palettes so that you can see which parts of the drawing will be hidden by the palettes after zooming.

door14-2s.jpg

Select the trim tool and click the right-hand vertical line as the reference object. Click inside the inner wall on both horizontal lines. Cancel the reference line with Escape and click the left-hand vertical line as the reference object. Click the horizontal lines inside the inside wall again because these are the parts we want to keep. That leaves the inside wall with a door opening.

door14-2s.jpg

Next we will draw the door path with a curve. Select the Arc Defined by a Center and Radius tool from the top left of the toolbox.

door14-2s.jpg

In the drawing, we need to mark a point that will be the center point for the curve. Click the junction of the upper short line of the door opening and the right-hand vertical line. The automatic catch mode will help you with the red circle. A small cross appears at the right-hand end of the line.

Enter 1 as the value at the bottom left next to Automatic mode or enter center point: as the curve will have a radius of one meter. Press Return to complete your entry. Alternatively you can also click the junction of the lower door edge with the vertical line.

Next you are asked with Automatic mode for start point or enter start angle: to enter, in our case, the start of the curve with an angle. Imagine there is a circle around the point marked first. The zero degrees position is on the right where east would be on a compass. As is standard in mathematics, the 90 degrees position is at the top where north is on a compass. There is an angle of 180 degrees at the west position and an angle of 270 degrees at the south position. As our curve stretches from "south pole" to "east pole", we should enter 270 degrees as the starting angle at the bottom left of the window and confirm with Return or click this point again. This query appears: Automatic mode for end point or enter end angle. Enter a zero and end the entries with Return. The curve is drawn for the door.

door14-2s.jpg

Finally we will draw another line from the open curve end to the broken wall. Disable infinity by clicking the infinity symbol.

We need the tool for drawing lines from point-to-point from the toolbox. Open the pop-up menu for the tool at the top left of the toolbox and select the point-to-point tool at the top left.

door14-2s.jpg

Click the open end of the curve. A small cross will appear at the end of the curve. Click the top short line of the doorway to the right of its center. CADintosh will draw a line between the two points.

door14-2s.jpg

>> 05 Labeling Objects

CADintosh入門 | 17:36:12 | Trackback(0) | Comments(-)
03 Split
Exciteで和訳する(参考)

In a proper architectural drawing, the joins between the inside walls and the outside walls are drawn open.

split12-2.jpg

Use the Split option to create these gaps. Select the Split tool from the third row of the righthand column in the toolbox using the pop-up menu. It is at the bottom left of the pop-up menu that opens.

split12-2.jpg

Click the top line of the horizontal inside wall so that it is highlighted red. Next click the inside line of the adjoining outer wall.

split12-2.jpg

CADintosh marks the point with a small cross. The line will be broken at the point marked with the cross. You cannot see a gap, however, because the two parts meet each other. We will reach our aim by deleting the part under the cross with the trim option. Select the trim option for sharp corners in the toolbox.

split12-2.jpg

Click the bottom line of the inside wall as it will be the "knife", i.e. the reference object. Then click the vertical line under the inside wall. The small part above the corner point will be deleted.

split12-2.jpg

The walls are now joined completely. If you want to remove the red marking of the reference line, press Escape. Repeat the break and trim process on the right-hand outside wall to practice.

You can break the two other points at the top and bottom on the small inside wall in one action.

Select the Split tool again and click the right-hand line of the vertical inside wall so that it is highlighted in red. Click the bottom line of the horizontal inside wall to the right of the vertical wall and also the inside line of the outer wall. The points where the lines have been split are indicated with a small cross.

split12-2.jpg

Select the trim option for sharp corners in the toolbox again.

split12-2.jpg

Click the left-hand line of the vertical wall as a “knife” and click the adjoining lines of the inside and outside wall to the left of the line highlighted in red.

split12-2.jpg

>> 04 A Door

CADintosh入門 | 11:20:24 | Trackback(0) | Comments(-)
02 The First Line
Exciteで和訳する(参考)

To draw the first line, click the top left tool in the toolbox. Hold down the mouse button. A popup menu opens where you can select the top right tool Line at an Angle.

line5-1.jpg

Enter 0,0 as the coordinates at the bottom left. You may find it easier to enter a space instead of the comma. A comma will be added automatically. Press Return to complete your entry.

line5-1.jpg

You will then be asked to enter the angle at the same point. Values that you do not need to change are preset in the entry box.

line5-1.jpg

The first value is the angle. The line is horizontal at 0.00 degrees. Instead of the comma, a period will appear in the first value because this is the international standard. The value for the length of the line comes after the comma: 100.00, i.e. 100 meters. This value is not significant because we selected infinite as the basic setting. Press Return to confirm these values. The line will then be drawn.

line5-1.jpg

In the entry section at the bottom left, you will be asked to enter the values for the next line. Enter 0,0 for the first line and confirm the entry with Return.

You will then be asked to enter the angle and length for the line. The last values entered always appear as the preset values. Enter 90 as the value for the angle. You do not need to enter a length because we enabled infinity. Press Return to complete your entry. A vertical line will appear.

line5-1.jpg

We need two more lines to make the base rectangle. To draw these lines, we will use the Parallel Lines option because this is the fastest method. Open the pop-up menu for the tool at the top left of the toolbox and select the second tool from the left in the top line.

line5-1.jpg

The mouse cursor will turn into a crosshair. At the bottom left of the window, you will be asked to click a line. This line will be the reference object. The new line will be drawn parallel to this reference line. Click above the horizontal line. You should not hit the line, but click just slightly above it as the new line will always be drawn on the side of the reference line where you click it. You can specify how far from the reference line you may click under Options / Mouse as Catch Radius.

line5-1.jpg

The line is highlighted red to identify it as the reference object for a moment. At the bottom left, you are asked to enter the spacing. As our house is 8 meters wide, enter 8 and confirm the entry with Return as usual. A parallel line will be drawn on the working area spaced exactly 8 meters from the first line.

If the second line is not displayed, you may have accidentally selected a different zoom level with the scroll wheel on your mouse. Select zoom level 100% using the + and - buttons at the top right of the window frame or turn the scroll wheel on your mouse until 100% appears on the right in the Position palette.

line5-1.jpg

Now click slightly to the right of the vertical line and enter the value for the spacing in the same way as for the line you just created. Our house will be 10 meters long. Enter 10 and end the entry with Return. CADintosh will draw a parallel line at a distance of 10 meters. So we have now drawn the basic rectangle for our house.

line5-1.jpg

In the next step, we will remove the overhanging lines. This is called trimming. Save the file and select the third tool from the top in the right-hand column.

line5-1.jpg

Select the Automatic Catch Mode (14) at the bottom of the window frame that you can use constantly apart from a few special cases.

When you use the trim option, you select an element that then more or less acts as a knife edge. If you click a second element, it is cut by the first one like with a knife. Click the right-hand vertical line. The line is highlighted red to identify it as the reference object for trimming. Now click the top horizontal line along the section that should be kept, i.e. between the crossings of the vertical lines. The part overhanging to the right will be trimmed and thus deleted.

line5-1.jpg

The right-hand vertical line is kept as a reference object. Click the middle of the bottom horizontal line between the junctions of the vertical lines to also trim the bottom horizontal lines.

Reset the reference line by pressing the Escape key. The right-hand vertical line no longer appears in red. Click the left-hand vertical line to set it as the reference object. Click the middle of the top and the bottom horizontal line between the junctions of the vertical lines to trim the overhanging lines on the left.

line5-1.jpg

Trim the remaining overhanging lines by canceling the reference object with Escape again and making the top and then the bottom horizontal line the reference object. Click the center areas to delete the overhangs as you have already done with the other lines. End trimming by switching to the tool for parallel lines at the top of the left-hand column in the toolbox.

Next we will draw the outside walls with their actual thickness using a second inside line. Click slightly to the right of the left-hand vertical line to draw a line parallel to it. At the bottom left of the window, you will be asked to enter the spacing for the new line. The walls will be 30 cm thick. Therefore enter 0.3 since the unit is meters. Press Return to complete your entry.

line5-1.jpg

The result is a parallel line that overruns infinitely in both directions and will therefore have to be trimmed later on. While the automatic catch mode is selected, a red circle with a cross will appear on the junctions and center points of lines to help you select these points precisely. You can ignore this display if, for example, you click a line just as a reference object.

line5-1.jpg

Now click the bottom horizontal line and confirm the suggested last entered value of 0.30 meters with Return. Click above the bottom horizontal line. CADintosh will draw the inside wall. Proceed in the same way with the two remaining walls. Do not forget to confirm the suggested value for the distance with Return otherwise the line will be drawn at the point you click and with the wrong distance.

line5-1.jpg

The overhanging lines need to be trimmed in the next step. Proceed as described above. Select the trimming tool in the toolbar (second column, third line). Click the second horizontal line from the top to trim along it. Click the two vertical lines inside the rectangle and proceed in the same way on all sides.

line5-1.jpg

From CADintosh 5.2, the drawing will be refreshed automatically after each action if you are using Mac OS X. You will therefore not see any gaps in the remaining lines even after deleting parts. Please only read the next paragraph if you are working with older versions.

Older versions of CADintosh (5.0.1 and older) will not redraw the content of the screen after each work step since this can take slightly longer with complex drawings and would be annoying. Therefore you will see small gaps in the lines at the points where they were covered by other lines that have been deleted. If you are using Mac OS X 10.2 and CADintosh 4.x or older, you can refresh the screen with F11 to display the lines continuously. Under Mac OS X 10.3 Panther, F11 is reserved for Exposé. CADintosh 5.0.1 therefore uses F12 for redraw. Alternatively you can turn the scroll wheel on your mouse one step back and forth or hold the Shift key and move the window section slightly with the mouse to trigger a redraw.

You can select the function key assignment freely under Options / Function Keys....

line5-1.jpg

Click the small “Z” button at the top right corner of the window to zoom the drawing until fills the window. Next we will draw an inside wall. Select the tool for parallel lines again and click the inside of the bottom wall. Enter 3 at the bottom left as the inside wall will be 3 meters from the selected outside wall. Press Return to complete your entry.

line5-1.jpg

Cancel the reference line with Escape. Select the new line as a reference line and draw another line over this line with a spacing of 0.22 meters using the same technique. Trim the new lines so that they end at the inside walls.

line5-1.jpg

The next inside wall will divide the bottom room into two rooms. Draw a line parallel to the right-hand wall at a distance of 5 meters and another line parallel to the new one at a distance of 0.22 m. Trim the new lines. The results should be the same as in the following screenshot.

line5-1.jpg

>> 03 Split

CADintosh入門 | 11:58:59 | Trackback(0) | Comments(-)


前のページ 次のページ
Search
Search this site.
Calender
- - 1 2 3 4 5
6 7 8 9 10 11 12
13 14 15 16 17 18 19
20 21 22 23 24 25 26
27 28 29 30 31 - -
07月 « 2017/08 » 09月
Recent Comments
Recent Trackbacks
Profile+Misc.

  • author: Makoto Inoue
  • 日本語ローカライズ担当




上記広告は1ヶ月以上更新のないブログに表示されています。新しい記事を書くことで広告を消せます。