スポンサーサイト
上記の広告は1ヶ月以上更新のないブログに表示されています。
新しい記事を書く事で広告が消せます。


スポンサー広告 | --:--:-- | Trackback(-) | Comments(-)
04 A Door
Exciteで和訳する(参考)

Next we will draw a door on the short inside wall. At the bottom left, select pen 2 that draws 0.35 mm thick lines. First draw a line parallel to the inside line of the bottom outside wall with a spacing of one meter and then another line parallel to the new line also with a spacing of one meter. The results should be the same as the following screenshot.

door14-2s.jpg

We only need the parts of the two new lines that are inside the inside wall. Zoom the picture to be make trimming easier. Hold down the Alt key and drag open a rectangle over the area to be enlarged. CADintosh does not only show a rectangle, but also all open palettes so that you can see which parts of the drawing will be hidden by the palettes after zooming.

door14-2s.jpg

Select the trim tool and click the right-hand vertical line as the reference object. Click inside the inner wall on both horizontal lines. Cancel the reference line with Escape and click the left-hand vertical line as the reference object. Click the horizontal lines inside the inside wall again because these are the parts we want to keep. That leaves the inside wall with a door opening.

door14-2s.jpg

Next we will draw the door path with a curve. Select the Arc Defined by a Center and Radius tool from the top left of the toolbox.

door14-2s.jpg

In the drawing, we need to mark a point that will be the center point for the curve. Click the junction of the upper short line of the door opening and the right-hand vertical line. The automatic catch mode will help you with the red circle. A small cross appears at the right-hand end of the line.

Enter 1 as the value at the bottom left next to Automatic mode or enter center point: as the curve will have a radius of one meter. Press Return to complete your entry. Alternatively you can also click the junction of the lower door edge with the vertical line.

Next you are asked with Automatic mode for start point or enter start angle: to enter, in our case, the start of the curve with an angle. Imagine there is a circle around the point marked first. The zero degrees position is on the right where east would be on a compass. As is standard in mathematics, the 90 degrees position is at the top where north is on a compass. There is an angle of 180 degrees at the west position and an angle of 270 degrees at the south position. As our curve stretches from "south pole" to "east pole", we should enter 270 degrees as the starting angle at the bottom left of the window and confirm with Return or click this point again. This query appears: Automatic mode for end point or enter end angle. Enter a zero and end the entries with Return. The curve is drawn for the door.

door14-2s.jpg

Finally we will draw another line from the open curve end to the broken wall. Disable infinity by clicking the infinity symbol.

We need the tool for drawing lines from point-to-point from the toolbox. Open the pop-up menu for the tool at the top left of the toolbox and select the point-to-point tool at the top left.

door14-2s.jpg

Click the open end of the curve. A small cross will appear at the end of the curve. Click the top short line of the doorway to the right of its center. CADintosh will draw a line between the two points.

door14-2s.jpg

>> 05 Labeling Objects
スポンサーサイト


CADintosh入門 | 17:36:12 | Trackback(0) | Comments(-)


Search
Search this site.
Calender
1 2 3 4 5 6 7
8 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30 31 - - - -
09月 « 2017/10 » 11月
Recent Comments
Recent Trackbacks
Profile+Misc.

  • author: Makoto Inoue
  • 日本語ローカライズ担当




上記広告は1ヶ月以上更新のないブログに表示されています。新しい記事を書くことで広告を消せます。