スポンサーサイト
上記の広告は1ヶ月以上更新のないブログに表示されています。
新しい記事を書く事で広告が消せます。


スポンサー広告 | --:--:-- | Trackback(-) | Comments(-)
00 CADintosh入門について
CADintosh入門は、Thorsten Lemke氏の許可を得て、Introduction.pdfをそのままコピーしているものです。"Exciteで和訳する(参考)"で日本語訳を見ることができますが、機械翻訳ではかえって解り難くしている箇所も多くあります。原文と共に流れを大まかに把握するのに利用していただければと思います。

※なお、初めてCADintoshをご使用になる方はユーザーズガイド(PDFファイル)の方をおすすめします。Classic版ではCADintosh JPフォルダの中にあります。X版ではメニューのヘルプから選択して開きます。その中のサンプル図をCADintoshで描いてみると操作の感じがつかめると思います。

目次
01 Introduction
02 The first Line
03 Split
04 A Door
05 Labeling Objects
06 Symbols
07 Editing Symbols
08 Managing Symbols
09 Hatching
10 Dimension
11 Move
12 Stretching

スポンサーサイト
CADintosh入門 | 13:00:26 | Trackback(0) | Comments(-)
05 Labeling Objects
Exciteで和訳する(参考)

Finally, we will draw a table that can be moved and rotated freely as an example of furniture. Using the pop-up menu, select the Line at an Angle tool from the top left of the toolbox.

labeling16-3.jpg

Select the Freehand (11) catch mode on the left and click the center of the top left room. At the bottom left of the window, you will be asked to enter the angle and length for the new line that will be drawn from the point you clicked. Enter a zero for the angle and 1.5 as the length.

labeling16-4.jpg

The first edge of the table will appear.

labeling17-1.jpg

Select the tool for drawing parallel lines and click below the line you just created. Enter 0.8 as the spacing at the bottom left and end the entry with Return.

Select the tool for point-to-point lines that we also used for the last line of the door path and select the automatic catch mode (14). Click the right-hand end of the upper line and then also the right-hand end of the bottom line of the table. CADintosh will join the two line ends with a line. Click the lines again, but this time at the left-hand end to connect the left-hand line ends.

labeling17-2.jpg

We will add a label so that the table is always recognizable as a table. Select the text tool from the right-hand column of the toolbar in the second line.

labeling17-3.jpg

Click the Freehand catch mode on the left and click the left-hand area inside the table. Enter "Table 1.5 x 0.8 m" as the text at the bottom left of the window. Press Return to complete your entry. The text will be too large at first.

labeling18-1s.jpg

Using the pop-up menu for the text tool, select the text tool for changing parameters:

labeling18-2.jpg

Click the text. A dialog with text settings opens. This may take a while if you have installed a large number of fonts.

labeling18-3s.jpg

Enter 1mm as the height. The font will then be shown smaller. Refresh the screen by pressing F12 as parts of the old font are sometimes left over.

You can use the freehand tool at the bottom right of the toolbox to move text objects freely. If you want to move text to a position in the drawing further away, it may be easier to select the move tool for text:

labeling19-1.jpg

Click the text and it will then be shown in a rectangle. Now click another point. The text will be moved to the point you clicked.

labeling19-2s.jpg


CADintosh入門 | 12:55:33 | Trackback(0) | Comments(-)


Search
Search this site.
Calender
1 2 3 4 5 6 7
8 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30 31 - - - -
04月 « 2005/05 » 06月
Recent Comments
Recent Trackbacks
Profile+Misc.

  • author: Makoto Inoue
  • 日本語ローカライズ担当




上記広告は1ヶ月以上更新のないブログに表示されています。新しい記事を書くことで広告を消せます。