スポンサーサイト
上記の広告は1ヶ月以上更新のないブログに表示されています。
新しい記事を書く事で広告が消せます。


スポンサー広告 | --:--:-- | Trackback(-) | Comments(-)
00 CADintosh入門について
CADintosh入門は、Thorsten Lemke氏の許可を得て、Introduction.pdfをそのままコピーしているものです。"Exciteで和訳する(参考)"で日本語訳を見ることができますが、機械翻訳ではかえって解り難くしている箇所も多くあります。原文と共に流れを大まかに把握するのに利用していただければと思います。

※なお、初めてCADintoshをご使用になる方はユーザーズガイド(PDFファイル)の方をおすすめします。Classic版ではCADintosh JPフォルダの中にあります。X版ではメニューのヘルプから選択して開きます。その中のサンプル図をCADintoshで描いてみると操作の感じがつかめると思います。

目次
01 Introduction
02 The first Line
03 Split
04 A Door
05 Labeling Objects
06 Symbols
07 Editing Symbols
08 Managing Symbols
09 Hatching
10 Dimension
11 Move
12 Stretching

スポンサーサイト
CADintosh入門 | 13:00:26 | Trackback(0) | Comments(-)
05 Labeling Objects
Exciteで和訳する(参考)

Finally, we will draw a table that can be moved and rotated freely as an example of furniture. Using the pop-up menu, select the Line at an Angle tool from the top left of the toolbox.

labeling16-3.jpg

Select the Freehand (11) catch mode on the left and click the center of the top left room. At the bottom left of the window, you will be asked to enter the angle and length for the new line that will be drawn from the point you clicked. Enter a zero for the angle and 1.5 as the length.

labeling16-4.jpg

The first edge of the table will appear.

labeling17-1.jpg

Select the tool for drawing parallel lines and click below the line you just created. Enter 0.8 as the spacing at the bottom left and end the entry with Return.

Select the tool for point-to-point lines that we also used for the last line of the door path and select the automatic catch mode (14). Click the right-hand end of the upper line and then also the right-hand end of the bottom line of the table. CADintosh will join the two line ends with a line. Click the lines again, but this time at the left-hand end to connect the left-hand line ends.

labeling17-2.jpg

We will add a label so that the table is always recognizable as a table. Select the text tool from the right-hand column of the toolbar in the second line.

labeling17-3.jpg

Click the Freehand catch mode on the left and click the left-hand area inside the table. Enter "Table 1.5 x 0.8 m" as the text at the bottom left of the window. Press Return to complete your entry. The text will be too large at first.

labeling18-1s.jpg

Using the pop-up menu for the text tool, select the text tool for changing parameters:

labeling18-2.jpg

Click the text. A dialog with text settings opens. This may take a while if you have installed a large number of fonts.

labeling18-3s.jpg

Enter 1mm as the height. The font will then be shown smaller. Refresh the screen by pressing F12 as parts of the old font are sometimes left over.

You can use the freehand tool at the bottom right of the toolbox to move text objects freely. If you want to move text to a position in the drawing further away, it may be easier to select the move tool for text:

labeling19-1.jpg

Click the text and it will then be shown in a rectangle. Now click another point. The text will be moved to the point you clicked.

labeling19-2s.jpg


CADintosh入門 | 12:55:33 | Trackback(0) | Comments(-)
おすすめ
コンピュータの使用感は、本体の性能もさることながら、人が直に接するインターフェイスとなるマウス、キーボード、モニタ等によってかなり左右されます。特にCADソフトウエアを使う上では言うまでもありません。

おすすめマウス
Microsoft IntelliMouse Optical多ボタンマウスによってCADの操作性を向上させることができます。私は5ボタンの Microsoft IntelliMouse Optical を使っています。USB端子のあるMacならばClassicでもXでも使用できます。

キーボードを使わずに右クリックだけでコンテクストメニューを出すことができます。スクロールボタンで画面の拡大、縮小ができます(Classicでは挙動が違うようです)。また、左右の側ボタンをそれぞれ「shift+クリック」、「option+クリック」に設定すれば画面のパン、ズームがマウスだけで操作できるようになります。

マウス(ソール)の滑りが不十分に感じられる場合はこちらを参照下さい→トスベールでマウスのソール(足)を改良する

おすすめマウスパッド
* ダイソー 光学マウス対応マウスパッド 105円
* UCHIDA 「きりっこ」 下敷きタイプのカッティングマット

リンク・紹介・お勧め | 11:58:26 | Trackback(0) | Comments(-)
リンク・紹介
* Lemke Software GmbH ドイツのシェアウエアメーカ。GraphicConverter、CADintosh、FontBook、SnapsCleaner
* Yahoo! Groups: cadintoshmac 英語です。CADintoshの作者Thorsten Lemke氏も参加しています
* シェアウエア登録 Kagi 登録料の支払いはこちらでお願いします。
* CADintosh JP 旧サイト
* VA034381 Makoto Inoueのサイト。SnapsCleanerJP、Pd、Zerius Vocoder

CADintoshの使用事例
* Metallbau Schlosserei Thomas Sauter 製作にCADintosh?とレーザーを使用しているドイツの鉄工ファクトリー。"TECHNOLOGIE"のページにCADintoshのスクリーンショット
* Fräsentagebuch ドイツの旋盤機メーカー?"Zum Thema Software"のページにCADintosh
* 軽模型飛行機研究室 - 非対称DLG:Mutant Bird
* ポコマンボの庭 - ポコ庭「恐竜フェンス」のできるまで

* アスキーMacPeople2004.3.15+4.1号で紹介、付録CD-ROM収録されました。
* 平成16年度CAD利用技術者試験1級(実技)にCADintoshが利用可能との回答をCAD利用技術者試験センターより得ました。DXFファイルでの提出ですので文字化け等に注意の上、自己責任で利用下さい。
* Vector 週間総合ランキング(Macintosh)04.02.02~04.02.08 Macintosh総合16位「CADintosh X 5.1」(ビジネス部門では1位)


リンク・紹介・お勧め | 11:40:49 | Trackback(0) | Comments(-)
04 A Door
Exciteで和訳する(参考)

Next we will draw a door on the short inside wall. At the bottom left, select pen 2 that draws 0.35 mm thick lines. First draw a line parallel to the inside line of the bottom outside wall with a spacing of one meter and then another line parallel to the new line also with a spacing of one meter. The results should be the same as the following screenshot.

door14-2s.jpg

We only need the parts of the two new lines that are inside the inside wall. Zoom the picture to be make trimming easier. Hold down the Alt key and drag open a rectangle over the area to be enlarged. CADintosh does not only show a rectangle, but also all open palettes so that you can see which parts of the drawing will be hidden by the palettes after zooming.

door14-2s.jpg

Select the trim tool and click the right-hand vertical line as the reference object. Click inside the inner wall on both horizontal lines. Cancel the reference line with Escape and click the left-hand vertical line as the reference object. Click the horizontal lines inside the inside wall again because these are the parts we want to keep. That leaves the inside wall with a door opening.

door14-2s.jpg

Next we will draw the door path with a curve. Select the Arc Defined by a Center and Radius tool from the top left of the toolbox.

door14-2s.jpg

In the drawing, we need to mark a point that will be the center point for the curve. Click the junction of the upper short line of the door opening and the right-hand vertical line. The automatic catch mode will help you with the red circle. A small cross appears at the right-hand end of the line.

Enter 1 as the value at the bottom left next to Automatic mode or enter center point: as the curve will have a radius of one meter. Press Return to complete your entry. Alternatively you can also click the junction of the lower door edge with the vertical line.

Next you are asked with Automatic mode for start point or enter start angle: to enter, in our case, the start of the curve with an angle. Imagine there is a circle around the point marked first. The zero degrees position is on the right where east would be on a compass. As is standard in mathematics, the 90 degrees position is at the top where north is on a compass. There is an angle of 180 degrees at the west position and an angle of 270 degrees at the south position. As our curve stretches from "south pole" to "east pole", we should enter 270 degrees as the starting angle at the bottom left of the window and confirm with Return or click this point again. This query appears: Automatic mode for end point or enter end angle. Enter a zero and end the entries with Return. The curve is drawn for the door.

door14-2s.jpg

Finally we will draw another line from the open curve end to the broken wall. Disable infinity by clicking the infinity symbol.

We need the tool for drawing lines from point-to-point from the toolbox. Open the pop-up menu for the tool at the top left of the toolbox and select the point-to-point tool at the top left.

door14-2s.jpg

Click the open end of the curve. A small cross will appear at the end of the curve. Click the top short line of the doorway to the right of its center. CADintosh will draw a line between the two points.

door14-2s.jpg

>> 05 Labeling Objects

CADintosh入門 | 17:36:12 | Trackback(0) | Comments(-)
03 Split
Exciteで和訳する(参考)

In a proper architectural drawing, the joins between the inside walls and the outside walls are drawn open.

split12-2.jpg

Use the Split option to create these gaps. Select the Split tool from the third row of the righthand column in the toolbox using the pop-up menu. It is at the bottom left of the pop-up menu that opens.

split12-2.jpg

Click the top line of the horizontal inside wall so that it is highlighted red. Next click the inside line of the adjoining outer wall.

split12-2.jpg

CADintosh marks the point with a small cross. The line will be broken at the point marked with the cross. You cannot see a gap, however, because the two parts meet each other. We will reach our aim by deleting the part under the cross with the trim option. Select the trim option for sharp corners in the toolbox.

split12-2.jpg

Click the bottom line of the inside wall as it will be the "knife", i.e. the reference object. Then click the vertical line under the inside wall. The small part above the corner point will be deleted.

split12-2.jpg

The walls are now joined completely. If you want to remove the red marking of the reference line, press Escape. Repeat the break and trim process on the right-hand outside wall to practice.

You can break the two other points at the top and bottom on the small inside wall in one action.

Select the Split tool again and click the right-hand line of the vertical inside wall so that it is highlighted in red. Click the bottom line of the horizontal inside wall to the right of the vertical wall and also the inside line of the outer wall. The points where the lines have been split are indicated with a small cross.

split12-2.jpg

Select the trim option for sharp corners in the toolbox again.

split12-2.jpg

Click the left-hand line of the vertical wall as a “knife” and click the adjoining lines of the inside and outside wall to the left of the line highlighted in red.

split12-2.jpg

>> 04 A Door

CADintosh入門 | 11:20:24 | Trackback(0) | Comments(-)


Search
Search this site.
Calender
1 2 3 4 5 6 7
8 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30 31 - - - -
04月 « 2005/05 » 06月
Recent Comments
Recent Trackbacks
Profile+Misc.

  • author: Makoto Inoue
  • 日本語ローカライズ担当




上記広告は1ヶ月以上更新のないブログに表示されています。新しい記事を書くことで広告を消せます。